FULL STOP!!! Smoke'm if you got'em...
Good News:
I got everything under the hood ready for the first run. I got the in-line preheater wrapped around the exhaust and the main heater will be finished next week. I used my cell phone bill money and filled up my water tank with fresh Spring water from Wally World today. Flushed out the line to the main high pressure pump. Blocked the exit and set the line pressure for 60psi and looked for leaks. I set the electronics to turn the water misters on at 400RPM and then I turned the main pump switch off (Manual Override). I did this because my first test is to see if I can make the Dodge run on 60psi of hot, misting, HHO concentrated water and plasma spark.
Check List For Test Run:
Brain? CHECK
MAIN POWER? CHECK
MAIN High Voltage Alternator power switch? CHECK
MAIN Electronics power switch? CHECK
Water tank float wired to electronics? CHECK
Tach wired to electronics? CHECK
Solenoid wired to electronics? CHECK
Obstruction monitor wired to electronics? CHECK
200PSI water pressure gage? CHECK
1000 volt Impedance Matching LRC Network? CHECK
Positive and Negative 6 inch tube cells? CHECK
Red and UV LED 3 inch tube cells? CHECK
80,000 volt intake air ionizer/ozonator? CHECK
Red and UV LEDs in air ionizer/ozonator? CHECK
High voltage plasma spark capacitors? CHECK
High voltage plasma spark diodes? CHECK
Spark plugs without resistors? CHECK
Water pre-heater tubing wrapped around exhaust pipe? CHECK
MAIN electric water heater(preset to 150*F)? NOT READY
Misting water temperature gage? NOT READY
Low pressure water primer pump wired? CHECK
High pressure water misting pump wired? CHECK
Water flows? CHECK
Electric fuel pump wired? CHECK
Fuel flows? CHECK
4 years of research? CHECK
Ugly from ear to ear? CHECK
Bad News:
I got the wrong torque converter and the other one won't show up for at least a week. I got to send a shout out to Jay at Broader Performance in Weatherford, Tx for being so patient with me and for all his support and knowledge. Please look into Broader Performance (817-599-9400) for your high performance transmissions and components. WWW.BroaderPerformance.Com ...the good guys.
I've gotten 500$ of the 1,000$ needed to finish this. I got 6$ to my name. I need 500$ more (little parts nickel and dime me to death!). I would like to have the 500$ by the end of next week.
I'm so excited!!! Its been 4 years and over 50 experiments you know? I have the receipts to prove it! Flat plate cells, caustic solutions, pressurized tanks, low volts and high amps, single phase, LRC, Impedance Matching, SR1 crap, Joe Cell crap, Bob Boyce crap, Pantone crap, HydroStar crap, Ravi crap, pulsing normal DC, Sully DC, in snow, in rain, in heat, 12-18 hours every day of the week including holidays. But I couldn't have done it without HUNDREDS of peoples help... this list is long and starts from 2 dollar donations and 20$ DVD sales (currently) all the way up to 2,000$ donations (past). Are you on this list or are you sitting on your ass like some bump?
When the Dodge runs on water the blog will disappear and clear directions will be made for all that wish to have them. Some parts and incomplete systems will be sold for Do-It-Yourselfers (vehicle and brains not included). There will also be a set date for the Water Powered Vehicle Race so you better get up to get down. Check around for the updates on my web site soon.
God works in mysterious ways. I wonder why I get the wrong parts and have to make 5 trips to find the one right part...but it always works out if I'm patient and calm (it helps to cry, cuss, and pray a lot too). Sometimes I come up with better ideas looking for parts I can't find. And if it wasn't for the running around I wouldn't have thought of that better idea. But one thing is for sure...that rushing things and doing a below standard job results in more work, more stress, more trips, and more money spent. Thanks Mom and Dad for instilling that in me. Now I know why yall don't have any politicians for friends.
Hurry up and get here next week!!! I've been waiting and working on you for almost 4 years. Good thoughts, positive energy, blessings and prayers, maybe a donation or two... do what you can for me because I don't need much right now.




Mr Epicdude, how goes it? Did you get it working and find something lacking, or are you still waiting to fire it up? Bought a DVD , I'm busted too otherwise. I tell you, that video where you turned on the vacuum and it just boiled away like mad instead of being a foaming agent, that was an eye opener.
Kevin wrote " still waiting on the tranny part"
Reply to this
Wow amazing it is a nice innovation, I think you are damn good at your work, This article has amazed me. Great concoction.
Reply to this